CLICK ON PICTURES TO ENLARGE. |
PART No.
PART / DESCRIPTION / DETAILS. |
CLICK ON PICTURES TO ENLARGE. |
PART No.
PART / DESCRIPTION / DETAILS. |
|
ZX6-R - 879
REAR CALIPER BRACKET & BOLTS - GOOD. |
|
ZX6-R - 884
RUBBER DUCT - VERY GOOD. |
|
ZX6-R - 885
STARTER MOTOR LEAD - GOOD. |
|
ZX6-R - 897
REAR WHEEL ADJUSTERS - GOOD WORKING ORDER, FINISH A LITTLE TATTY. |
|
ZX6-R - 919
RIGHT SIDE CALIPER BRACKET - GOOD. |
|
ZX6-R - 024B
REGULATOR / RECTIFIER - SH650-12 - VERY GOOD, WORKING. NOTE: THIS ONE HAS TWO ROUNDS PLUGS. |
|
ZX6-R - 025B
REGULATOR / RECTIFIER - SH650-12 - VERY GOOD, WORKING. NOTE: THIS ONE HAS ONE SQUARE PLUG. |
|
ZX6-R - 034B
PAIR OF BATTERY LEADS - VERY GOOD. |
|
|
ZX6-R - 877
STARTER MOTOR - VERY GOOD, WORKING WELL. PART NoS. 21163-1304 // 228000-7351. |
|
|
ZX6-R - 887
PAIR OF THROTTLE CABLES - SERVICEABLE, ONE HAS A TINY SPLIT IN OUT COVER. |
|
|
ZX6-R - 896
FRONT WHEEL SHAFT - VERY GOOD, 34cm LONG, 25mm DIAMETER, FAT END IS 52mm BY 31mm. |
|
|
ZX6-R - 907
FRONT BRAKE HOSE 1 PIECE - VERY GOOD. |
|
|
ZX6-R - 913
REAR WHEEL SHAFT & SPACERS ETC - GOOD, 25mm DIAMETER, 36cm LONG. |
|
|
ZX6-R - 914
REAR WHEEL SHAFT - GOOD, 25mm DIAMETER, 36cm LONG. |
|
|
ZX6-R - 936
EXHAUST SILENCER / CAN SUPPORT BRACKET - VERY GOOD, WILL FIT APPROX 10.5cm TO 11.5cm DIAMETER CAN. |
|
|
ZX6-R - 031B
STARTER SOLENOID & LEADS - VERY GOOD, TESTED. NOTE SLIGHTLY DIFFERENT FROM 032B BELOW. |
|
|
ZX6-R - 032B
STARTER SOLENOID & MOUNTING RUBBER - VERY GOOD, TESTED. NOTE SLIGHTLY DIFFERENT FROM 031B ABOVE - STAMPED WITH NUMBER MR5. |
|
|
ZX6-R - 038
STARTER SOLENOID WITH CABLES - VERY GOOD, TESTED. FROM A J1 J2 MODEL. |
|
|
ZX6-R - 039
OMRON RELAY 27002-1086 // 3011D6 - VERY GOOD, TESTED. FROM A J1 J2 MODEL. I HAVE TWO OF THESE. |
|
|
ZX6-R - 040
2-PIN DENSO RELAY - CAN'T QUITE READ THE NUMBER. WIRE COLURS WERE YELLOW WITH BROWN STRIP AND ORANGE WITH SILVER STRIP. FROM A J1 J2 MODEL. |
|
|
|
ZX6-R - 902
LEFT SIDE REAR FOOT REST MOUNTING & PEG - GOOD, NO DAMAGE, PAINT POOR. |
|
|
|
ZX6-R - 908
FRONT BRAKE LEVER - VERY GOOD. |
|
|
|
ZX6-R - 920
RIGHT SIDE CALIPER - VERY GOOD, WORKING WELL, PISTONS & SEALS AND BOTH THREADS ALL OK, USEABLE PADS. |
|
|
|
BLEED SCREW NOT SEIZED IN. |
|
|
|
ZX6-R - 939
EXHAUST CONNECTING PIPE - STAINLESS STEEL, INSIDE DIAMETER @ CLAMPS END IS 43mm, OUTSIDE DIAMETER @ OTHER END 48mm. |
|
|
|
ZX6-R - 037B
WIRING HARNESS - VERY GOOD AND ORIGINAL, FROM A J1 J2 MODEL - WITH FUSEBOX 26021-1095. |